Skip to main content

Bosch 2-Cutter SDS Drill Bits: Plus-1, Plus-3, Plus-5 and Max-2

Bosch's three standard metric SDS-Plus two-cutter series are SDS plus-1, plus-3 and plus-5. SDS max-2 is the two-cutter series for SDS-Max rotary hammers.

Author Zhonghuan Engineering Team
Published 2026-11-16
Reading Time 5 min read

Need Help Choosing a Tool?

Share your application, required dimensions and quantity. Our engineering team can recommend a product and confirm pricing and lead time.

Request Engineering Quote
Bosch SDS plus-5 drill bit, drawing with diameter D and lengths L1 and L2, and retail case
Bosch SDS plus-5 with a dimension sketch and retail case

Key Specification / Takeaways

  • 01. Four standard metric series. Plus-1, plus-3 and plus-5 fit SDS-Plus hammers. Max-2 fits SDS-Max hammers.
  • 02. Count the two main cutting edges at the tip. Four spiral flutes carry powder along the body on plus-3 and plus-5.
  • 03. Both selected part numbers have 100 mm working length. The five millimetres are a difference in total length.

Which Bosch SDS drill bits have two cutters?

The cutter count refers to the two main edges at the head. The flute count describes the channels along the steel body. The shank determines which rotary hammer chuck the bit fits. A two-cutter can have four dust flutes.

Bosch Taiwan uses 四溝 (four grooves) for the SDS-Plus chuck interface and 五溝 (five grooves) for SDS-Max. Bosch Taiwan SDS terminology

SeriesHead and flutesTotal codesSingle packs
SDS plus-1Two U-shaped flutes5240
SDS plus-3Centring point, four Dura flutes8080
SDS plus-5Grooved carbide tip, four Turbo flutes7060
SDS max-2Two U-shaped flutes2121
Total223201

Counts are by order code on Bosch India's product pages and include single bits, multipacks and mixed sets.

Bosch series comparison · Bosch max-2 technical data

SDS plus-1 with two U-shaped flutes

Bosch specifies a tungsten carbide plate with two cutting edges for the SDS plus-1. The two U-shaped flutes run along the steel body and carry drilling dust out of the hole. In the head photo, follow the carbide plate into the first turn of the spiral to see where the flutes pick up dust. Bosch lists concrete and solid brick among this series’ applications.

Bosch India lists two Ø8 mm examples. Part 2608680270 has a 100 mm working length and 160 mm overall length. Part 2608680271 has a 150 mm working length and 210 mm overall length. Choose the working length for the hole depth and check the overall length if space around the hammer is limited.

Bosch product specifications

Bosch SDS plus-1 with a close-up of the carbide head and drilling images
Head close-up and drilling views. The Ø10 mm package lists 100 mm working length and 160 mm overall length.
Packaging label for Bosch SDS plus-1 order code 2608579426
2608579426 · Ø8 mm · 150 mm working length · 210 mm overall length

SDS plus-3 centring point and Dura flutes

Bosch’s range comparison lists a centring point for the SDS plus-3. It helps position the bit as the hole starts. Four Dura flutes on the body carry the dust produced by the two cutting edges. Bosch UK also specifies indented carbide cutting edges and a high-alloy steel body with optimised hardening for wear resistance.

Part 2608831019 is Ø8 mm with a 100 mm working length and 160 mm overall length, the same dimensions as the short plus-1 example above. With the sizes matched, you can compare the tip shape and flute design directly.

Bosch product specifications · Bosch series comparison

Full Bosch SDS plus-3 drill bit showing the tip, flutes and SDS-Plus shank
SDS plus-3 drill bit · 2608831011
Bosch SDS plus-3 packaging for order code 2608831011
Ø6.5 mm · 50 mm working length · 110 mm overall length

How the SDS plus-5 tip moves dust

On a hard, smooth concrete face, check where the bit first makes contact. The raised point on the small-diameter SDS plus-5 helps locate the start. Plus-3 also has a centring point, so the point alone does not tell you which bit you are holding. Use the head close-up to follow the carbide toward the spiral.

SDS plus-5 head detail showing the carbide plate and the start of the spiral
SDS plus-5 head detail showing the carbide plate and the start of the spiral

In the Bosch profile drawing, V-shaped relief grooves in the carbide plate give powder a path from the bottom of the hole into the spiral. The four Turbo flutes then carry the powder along the body. The grooved plate and the spiral handle different parts of the same job. The brochure shows the design purpose. To compare evacuation speed against the plus-3 Dura geometry, use matched samples.

The wear mark is a reference for checking diameter wear on the head. For a metal anchor, use the anchor manufacturer's specified diameter, hole depth and cleaning method. Bosch also lists AWB brazing and hardening for plus-5. Treat that as a construction detail when comparing samples.

Bosch carbide profile drawing · Bosch plus-5 technical data

Full bit showing the head, spiral and SDS-Plus shank
Full bit showing the head, spiral and SDS-Plus shank
Packaged view. Use the printed part number for ordering.
Packaged view. Use the printed part number for ordering.

SDS max-2 shank diameter and working length

The SDS max-2 has two cutting edges and two U-shaped flutes. The two Ø20 mm references below both use an 18 mm SDS-Max shank. The shank diameter describes the part that fits the chuck. The bit diameter gives the nominal hole size.

At Ø20 mm, part 2608578014 gives a 195 mm working length and 340 mm overall length. Part 2608578017 gives 395 mm working length and 540 mm overall length. Choose the required reach at the same hole diameter, and check that Ø20 mm is within the rotary hammer manufacturer’s specified drilling range.

Bosch product specifications

Full view of the Bosch SDS max-2 drill bit with its carbide tip, flutes and SDS-Max shank
Bosch SDS max-2 drill bit
Side view of an SDS max-2 drill bit showing the shank, spiral flutes and carbide tip
Side view of the flutes and SDS-Max shank

Three Ø8 mm bits with 100 mm working length

The three SDS-Plus bits below all have an 8 mm diameter and a 100 mm working length (L1). Their overall lengths (L2) are 160 or 165 mm. Use the full part number to order the correct variant. The cited Bosch tables list dimensions and pack quantity and omit bit-only mass. For freight or mass comparisons, weigh the exact bit without its packaging.

Bosch seriesPart numberDiameter DWorking length L1Total length L2
SDS plus-126086802708 mm100 mm160 mm
SDS plus-326088310198 mm100 mm160 mm
SDS plus-526085791788 mm100 mm165 mm

How to choose a Bosch two-cutter bit

Check your rotary hammer’s chuck first. Choose SDS plus-1, plus-3 or plus-5 for SDS-Plus, or SDS max-2 for SDS-Max. Match the bit diameter to the required hole size and choose a working length (L1) that reaches the specified hole depth.

24-hour response guaranteed

Get a Quote for Your Spec

Tell us what you need. Our team responds within 24 hours with pricing and lead time.

sales@zhonghuantools.com

Products and Engineering Support

Match the tool to your application, compare product options, or ask our engineers to confirm a specification.

Run the Drilling & Cutting Selector

Choose the drilling or sawing task, machine and job condition, then carry the matched program into the RFQ.

Open System Selector

Build Your SDS OEM Range

Compare SDS-Plus and SDS-Max constructions, sampling and private-label supply.

View SDS OEM Program

Request Engineering Quote

Submit key details and receive a more qualified response on pricing and lead time.

Contact Engineering
#Bosch #SDS-Plus #SDS-Max #2-Cutter #SDS plus-5