Skip to main content

Hilti SP-H vs SP-H Abrasive Core Bits — What Changes at Ø102 × 450 mm?

Author Zhonghuan Engineering Team
Published 2026-11-20
Reading Time 6 min read

Need Help Choosing a Tool?

Share your application, required dimensions and quantity. Our engineering team can recommend a product and confirm pricing and lead time.

Request Engineering Quote
Hilti DD 250 on a stand during wet wall coring, as shown in the SP-H Abrasive application gallery
Figure 1.0: Hilti SP-H vs SP-H Abrasive Core Bits — What Changes at Ø102 × 450 mm? Overview

Key Specification / Takeaways

  • 01. Hilti lists two DD-B bits at Ø102 × 450 mm. SP-H #2158266 is for general concrete and SP-H Abrasive #2158237 is for very abrasive concrete.
  • 02. Abrasiveness describes how quickly the material wears the segment’s metal bond. Steel content and aggregate hardness are separate selection inputs.
  • 03. Confirm whether the order covers the bare barrel or a drill-ready assembly. For the latter, specify the actual chuck and matching connection end.

Two Hilti core bits at the same diameter and working length

If you are buying a Ø102 mm wet diamond core bit for reinforced concrete, Hilti offers a useful example. The SP-H #2158266 and SP-H Abrasive #2158237 both carry the B 102/450 designation. The difference that matters on the order is the concrete they are meant to cut.

Hilti positions both families for rig-mounted wet coring on tools rated at least 2.5 kW. Regional product pages list machines such as the DD 200 and DD 250-CA. The standard SP-H technical page lists 10 mm laser-welded segments. Hilti also specifies Equidist diamond placement for the two families from Ø35 mm. Diamond placement describes where the grits sit. The order still needs the segment specification for the exact bit.

SpecificationHilti SP-HHilti SP-H Abrasive
Item number21582662158237
Diameter × working lengthØ102 × 450 mmØ102 × 450 mm
Catalogue applicationGeneral concreteVery abrasive concrete
Drilling modeRig-mounted wet coringRig-mounted wet coring
Hilti SP-H for general concrete. The catalogue image uses a gray mark.
Hilti SP-H for general concrete. The catalogue image uses a gray mark.
Hilti SP-H Abrasive for very abrasive concrete. The catalogue image uses a green mark.
Hilti SP-H Abrasive for very abrasive concrete. The catalogue image uses a green mark.

Hilti uses gray for concrete and green for abrasive concrete in this catalogue. Confirm the item number when ordering.

Hilti colour coding

Hilti Hong Kong item record · Abrasive item listing · Hilti SP-H technical data · Hilti Abrasive technical data · Application photo source

Start at the cutting end when you read a product photo. The gaps between segments provide space for water and slurry. The metal bond holds the diamonds inside each segment. Equidist describes the placement of those diamonds inside the segment, while 10 mm describes the physical height reported for the regular SP-H family. To compare two bits, record segment count, width and height separately from how the diamonds are arranged. Match the bond to the material and judge performance in the hole.

Hilti Equidist segment detail showing the pattern of diamond positions.
Hilti Equidist segment detail showing the pattern of diamond positions.

Hilti segment photo source

What very abrasive concrete does to a core bit

The diamonds cut. The metal bond holds them and gradually wears to expose fresh grit. When the concrete and drilling slurry wear the bond too quickly, the segments can lose height before the diamonds have done their full share of cutting. That is the wear pattern the Abrasive application is meant to address.

Rebar density, aggregate hardness and abrasiveness are three different inputs. A rebar-dense wall can still be a job for standard SP-H. When a bit cuts slowly and its segment faces look polished, first check water delivery, speed, feed and the material at the hole. A bond that resists wear can help on very abrasive concrete. Dense, hard aggregate can call for a bond that exposes fresh grit more readily. Match the bond to the wear you observe on the actual job.

Core-bit bond selection reference

What the worn bit can tell you on site

Think of a mechanical contractor drilling repeated Ø102 mm sleeve holes. Record what happens to the crown after several holes in the same material. A quick check of the segment face and remaining height often gives a better lead than a description such as ‘hard concrete’.

  • Speed is stable and wear is even. The general-concrete bit is a reasonable starting point. Confirm it against the job’s expected hole count and depth.
  • It keeps cutting but loses segment height quickly. Inspect the crown around its full circumference. If wear is broadly even and water flow and setup are correct, abrasive fines may be using up the bond too quickly. An abrasive-concrete specification is worth sampling.
  • It slows down and the face turns glossy. Check water flow, speed, feed and rig alignment. A polished face can indicate poor diamond exposure. Ask for a freer-cutting bond as a sample option when the same result persists in dense aggregate under stable conditions.

Compare samples on the same rig, diameter and concrete. Record the drilling depth as well as the time and loss of segment height per completed hole. A bit with good first-hole speed can still be a poor choice for a batch of penetrations if it consumes the crown quickly.

Check what is included at the back of the bit

Hilti lists configurations with no connection end. That is a barrel supplied without the piece that mates to the machine. Hilti’s separate BL (M41) end illustrates the distinction. BL identifies the Hilti machine-side connection and M41 identifies the thread that mates to the coring insert on that connector. Verify the barrel and chuck together before buying the end.

Hilti BL (M41) connection end

Hilti catalogue illustration showing the wet core bit and a separate connection end.
Hilti catalogue illustration showing the wet core bit and a separate connection end.

For example, Hilti lists the DD 250-CA with BL or BS chucks. A 1¼-7 UNC core bit is specified for a matching BS connection. If the machine has a BL chuck, check the applicable Hilti BL-to-BS adapter and the complete assembly before ordering.

Hilti chuck chart · Hilti BL-to-BS adapter

Hilti lists a separate brazeable crown for re-tipping a suitable SP-H barrel. It is a front-end repair component. A new core bit and a machine-side connection end are separate purchase items.

Hilti SP-H Abrasive brazeable crown for retipping a suitable barrel.
Hilti SP-H Abrasive brazeable crown for retipping a suitable barrel.

Hilti retipping crown

Zhonghuan Tools OEM diamond core bits and application support

Zhonghuan Tools provides OEM and private-label diamond core bits for importers, distributors and tool brands. Our team can take the current bit, label or drawing as a starting point, check the fitted chuck and confirm a wet-coring specification suited to the job. We coordinate the drawing and evaluation sample, then quote the batch with your marking and packaging requirements.

For the same nominal size discussed here, our published ARIX Rev. E Ø102 × 450 mm specification has a 1¼-inch connection, 2.0 mm barrel wall and nine laser-welded ordered-array segments. Each segment is 24 × 3.5 × 12 mm. That gives us a documented starting point for sample discussion. On a highly abrasive job, we confirm the required bond and connector for the specific machine and agree how the sample will be evaluated on the customer’s concrete.

  1. Match the job. Send the rig model or a photo of the installed chuck, hole diameter × effective working length, material and quantity by size.
  2. Confirm the specification. We review the machine-side connection, barrel and wet-drilling segment together. A worn-bit photo or existing sample helps when the priority is faster cutting or better wear life.
  3. Approve a sample and move to bulk. Use the recorded drilling time and crown wear to agree the supply specification, then confirm private-label marking and packaging with the order.
Zhonghuan Tools ARIX ordered-array wet diamond core-bit programme.
Zhonghuan Tools ARIX ordered-array wet diamond core-bit programme.

Zhonghuan ARIX Rev. E specification and size matrix · OEM and private-label supply · Contact Zhonghuan about OEM diamond core bits

24-hour response guaranteed

Get a Quote for Your Spec

Tell us what you need. Our team responds within 24 hours with pricing and lead time.

sales@zhonghuantools.com

Products and Engineering Support

Match the tool to your application, compare product options, or ask our engineers to confirm a specification.

Validate Cutting Parameters

Use the calculator to confirm speed and application match before product selection.

Open RPM Calculator

Review Product Options

Compare relevant product lines and narrow down suitable series quickly.

View Product Catalog

Request Engineering Quote

Submit key details and receive a more qualified response on pricing and lead time.

Contact Engineering
#Hilti SP-H #Hilti SP-H Abrasive #Hilti Equidist #Diamond Core Bits